Deciding to have new flooring installed in your home can add value, transform the look and feel of a room and freshen the space up. Since most people hire a company for flooring installation in Dallas, TX, few homeowners know how the process works. Here are the steps for flooring flooring installation in Dallas, TX.
1. Removing the Old Flooring:
The very first step is to remove the old flooring. If you have carpet, this is a very easy process. The carpet is pulled upward, rolled up and taken outside. However, if you have hardwood, tile or linoleum, the process is much more difficult. Depending on what was used to install the flooring, an adhesive removed may be needed, each plank or tile may need to be popped up by hand or jackhammer may be needed. This process can take as little as one hour or several days.
2. Repairing the Subfloor:
The next step for flooring installation in Dallas, TX is repairing the subfloor. The subfloor is the concrete pad that your flooring lies on top of. If there is nothing wrong with the subfloor, this step is skipped. However, if there is any damage, it needs to be repaired. The most common type of damage is cracks in the subfloor. As the ground underneath your home shifts, the subfloor shifts. This can cause small cracks. However, it is important that these cracks be filled in and sealed, otherwise moisture from under the home can come up through these cracks. This can cause your linoleum to bubble, your carpet to mildew or your wood or vinyl floor to warp. In addition to this type of damage, damage can also be done to the subfloor while your old flooring is removed. If a jackhammer is used, it is very common for the subfloor to get nicked and dented. It is important to fill in these dings and dents, so the floor is level.
3. Laying the Plastic or Padding:
It is very rare that flooring is laid directly on the subfloor. Typically, a thin piece of plastic or padding is laid between the subfloor and the flooring. Therefore, the next step in the Dallas, TX flooring installation process is to lay that plastic or padding. Usually, it is a simple process. A roll of plastic or padding is rolled out over the space, pulled tightly into place and cut to size. It is then either glued or tacked into place.
4. Cutting Tiles or Planks:
If you are having tiles or hardwood or vinyl planks installed, the next step the installer takes is to cut those pieces to size. Most installers cut the pieces before they begin working, so they can install everything at one time, without having to install, stop and cut pieces and then install again.
5. Laying the Flooring:
The next step is to lay the flooring. The method used for laying flooring depends on the type of flooring that is being installed. If you are having tiles installed, a product called thin-set is applied to the back of each tile, and the tile is then placed onto the floor by hand. The thin-set dries and holds the tiles firmly in place. If you are having vinyl planks installed, they usually snap together, much like a puzzle. If you are having hardwood installed, the planks are typically held into place with glue or adhesive. If carpet is being laid, tack strips are placed into the corners of the room. Carpet is rolled out and secured into place with these strips. And lastly, if linoleum is being placed, an adhesive is placed and then the linoleum is rolled directly onto the adhesive.
1. Removing the Old Flooring:
The very first step is to remove the old flooring. If you have carpet, this is a very easy process. The carpet is pulled upward, rolled up and taken outside. However, if you have hardwood, tile or linoleum, the process is much more difficult. Depending on what was used to install the flooring, an adhesive removed may be needed, each plank or tile may need to be popped up by hand or jackhammer may be needed. This process can take as little as one hour or several days.
2. Repairing the Subfloor:
The next step for flooring installation in Dallas, TX is repairing the subfloor. The subfloor is the concrete pad that your flooring lies on top of. If there is nothing wrong with the subfloor, this step is skipped. However, if there is any damage, it needs to be repaired. The most common type of damage is cracks in the subfloor. As the ground underneath your home shifts, the subfloor shifts. This can cause small cracks. However, it is important that these cracks be filled in and sealed, otherwise moisture from under the home can come up through these cracks. This can cause your linoleum to bubble, your carpet to mildew or your wood or vinyl floor to warp. In addition to this type of damage, damage can also be done to the subfloor while your old flooring is removed. If a jackhammer is used, it is very common for the subfloor to get nicked and dented. It is important to fill in these dings and dents, so the floor is level.
3. Laying the Plastic or Padding:
It is very rare that flooring is laid directly on the subfloor. Typically, a thin piece of plastic or padding is laid between the subfloor and the flooring. Therefore, the next step in the Dallas, TX flooring installation process is to lay that plastic or padding. Usually, it is a simple process. A roll of plastic or padding is rolled out over the space, pulled tightly into place and cut to size. It is then either glued or tacked into place.
4. Cutting Tiles or Planks:
If you are having tiles or hardwood or vinyl planks installed, the next step the installer takes is to cut those pieces to size. Most installers cut the pieces before they begin working, so they can install everything at one time, without having to install, stop and cut pieces and then install again.
5. Laying the Flooring:
The next step is to lay the flooring. The method used for laying flooring depends on the type of flooring that is being installed. If you are having tiles installed, a product called thin-set is applied to the back of each tile, and the tile is then placed onto the floor by hand. The thin-set dries and holds the tiles firmly in place. If you are having vinyl planks installed, they usually snap together, much like a puzzle. If you are having hardwood installed, the planks are typically held into place with glue or adhesive. If carpet is being laid, tack strips are placed into the corners of the room. Carpet is rolled out and secured into place with these strips. And lastly, if linoleum is being placed, an adhesive is placed and then the linoleum is rolled directly onto the adhesive.