Lighting your gas fire place is important to be able to encounter the warmth and magnificence that they can give. Contrary to a conventional wood burning up fireplace, a gas fire place is often self starting. Not like an electric fire place, a gas fireplace demands use of a pilot light in order to ignite, much like water heater or a gas stove.
Try looking in your own fire place to find out if you find a small flame, which is called the initial light. If you don't see this particular flame, then you should first light up the pilot before you can start your gas fireplace.
If you have an attractive front panel or grill on your own gas fire place, at all times take it off just before lighting your pilot. Your own valves might be positioned at the rear of a panel. If that's so, locate this particular panel and open it up to access your valves and controls. Make sure all of your controls are off and that the pilot is really shut off.
Check to make certain that the main gas valve and control valve are switched off. In case the control valve or main gas valve is on, switch it off and hold on around five minutes to allow any gas to clear before you continue. These essential steps will allow you to prevent accidents along with your gas fire place. Take away any inner glass doors if you have not already done this.
Smell all over the fire place to make sure that there is no gas present that might ignite as you switch on the pilot. Be sure you sniff around near the floor because the gas is heavier as opposed to the surrounding air. If there is, allow the fire place to air out not less than five minutes before you carry on. In case the gas odor doesn't clear and you've checked out again to make sure that all valves are turned off, you will want to speak to a technician to find out if there are any leaks.
If there is no gas smell present, turn the main valve on and the control valve to pilot. Press the control valve in about one-fourth of an inch as you are turning. If you can't push the control valve inward using just your hand, call a skilled specialist. Do not use any equipment to attempt to push the control valve. Forcing the valve isn't just a fire hazard, but may also lead to explosion.
Press the pilot valve in at least fifteen seconds but up to thirty seconds and push the piezoelectric spark igniter repeatedly in an interval of once for every second to switch the pilot light on. Once the pilot light is turned on, a tiny flame should appear. In case the pilot light won't remain on after repeated attempts, call up a qualified specialist.
Press the pilot valve in for 60 seconds or more to be able to heat up your thermopile. When the thermopile has been warmed up, your burner will start. When burner is turned on, switch the control valve to on and change the thermostat to your preferred configurations. The thermostat control may be a turn in the bottom panel, dimmer, a standard light switch, or it may be started employing a remote control.
Change the inner glass door, any bottom access panel, ornamental glass panel or grill and make sure it's properly clamped to the front of your fire place. Enjoy your fireplace!
Try looking in your own fire place to find out if you find a small flame, which is called the initial light. If you don't see this particular flame, then you should first light up the pilot before you can start your gas fireplace.
If you have an attractive front panel or grill on your own gas fire place, at all times take it off just before lighting your pilot. Your own valves might be positioned at the rear of a panel. If that's so, locate this particular panel and open it up to access your valves and controls. Make sure all of your controls are off and that the pilot is really shut off.
Check to make certain that the main gas valve and control valve are switched off. In case the control valve or main gas valve is on, switch it off and hold on around five minutes to allow any gas to clear before you continue. These essential steps will allow you to prevent accidents along with your gas fire place. Take away any inner glass doors if you have not already done this.
Smell all over the fire place to make sure that there is no gas present that might ignite as you switch on the pilot. Be sure you sniff around near the floor because the gas is heavier as opposed to the surrounding air. If there is, allow the fire place to air out not less than five minutes before you carry on. In case the gas odor doesn't clear and you've checked out again to make sure that all valves are turned off, you will want to speak to a technician to find out if there are any leaks.
If there is no gas smell present, turn the main valve on and the control valve to pilot. Press the control valve in about one-fourth of an inch as you are turning. If you can't push the control valve inward using just your hand, call a skilled specialist. Do not use any equipment to attempt to push the control valve. Forcing the valve isn't just a fire hazard, but may also lead to explosion.
Press the pilot valve in at least fifteen seconds but up to thirty seconds and push the piezoelectric spark igniter repeatedly in an interval of once for every second to switch the pilot light on. Once the pilot light is turned on, a tiny flame should appear. In case the pilot light won't remain on after repeated attempts, call up a qualified specialist.
Press the pilot valve in for 60 seconds or more to be able to heat up your thermopile. When the thermopile has been warmed up, your burner will start. When burner is turned on, switch the control valve to on and change the thermostat to your preferred configurations. The thermostat control may be a turn in the bottom panel, dimmer, a standard light switch, or it may be started employing a remote control.
Change the inner glass door, any bottom access panel, ornamental glass panel or grill and make sure it's properly clamped to the front of your fire place. Enjoy your fireplace!